antiwrap axle template.JPG
2612 hits | 59.69 KB | Posted: 2/7/05
I used two peices of 1/4" plate steel about 6" x 8" and made template to "fit" what I had. When I d...

cleaning the axle.JPG
1487 hits | 80.81 KB | Posted: 2/7/05

grinding the axle.JPG
1335 hits | 80.81 KB | Posted: 2/7/05
Too bad there were no pictures taken when I set my sock and foot on fire while welding the bracket o...

closeup of top anti wrap bar.JPG
1476 hits | 78.54 KB | Posted: 2/7/05

view of top antiwrap with dom in square tube.JPG
1494 hits | 94.81 KB | Posted: 2/7/05
The top and bottom bars are 1.5" x .25" DOM tubing. The top bar is about 36" long, the bottom bar i...

bottom view.JPG
2588 hits | 90.85 KB | Posted: 3/18/05
Installed picture before painting.

pic of shackle mount 37 inches by 2x3 inch 11 .jpg
1852 hits | 56.55 KB | Posted: 4/28/05
Picture of shackle mount while I was painting it. It is 37" long, 2"x 3" 11 gauge rectangle tube. ...

closeup of shackle mount 2 inch square tube.jpg
1785 hits | 40.1 KB | Posted: 4/28/05
Closeup detail of where the square tubing for the actuall shackle mounts. It was 7" from the left e...

back view of shackle mount installed without s.jpg
1583 hits | 49.69 KB | Posted: 4/28/05
View of shackle mount installed, looking forward.

side view of shackle installed front hole for .JPG
1853 hits | 29.03 KB | Posted: 4/28/05
Side view of shackle mount. The front hole in the mount is where the shackle will bolt in. The top...

closeup of shackle two weld in bungs with tube.jpg
1524 hits | 42.75 KB | Posted: 4/28/05
Closeup of shackle, it was made out of two 5/8" weld in bungs, one left hand thread one right hand t...

another view of shackle.jpg
1381 hits | 45.12 KB | Posted: 4/28/05
Just another view of the shackle assembly, note the 1/4" spacers to allow more right/left movement w...

front view of axle plates installed.JPG
1393 hits | 45.48 KB | Posted: 4/29/05
Cruddy picture of the axle plates welded onto the Sterling. Look at those welds, can you say buble...

second view of axle plates installed.JPG
1448 hits | 47.69 KB | Posted: 4/29/05
Second picture of axle plates installed on Sterling. Not much better of a picture.

from rear of axle.JPG
1836 hits | 89.07 KB | Posted: 5/6/05
View of setup from rear of axle.

SRE and Bung shackle.JPG
1841 hits | 69.26 KB | Posted: 5/6/05
Heim (SRE) and bung shackle picture 1/4.

SRE and Bung shackle 2.JPG
1507 hits | 73.23 KB | Posted: 5/6/05
SRE shackle 2/4.

SRE and Bung shackle 3.JPG
1455 hits | 68.26 KB | Posted: 5/6/05
SRE and bung picture 3/4.

SRE and Bung shackle 4.JPG
1454 hits | 64.47 KB | Posted: 5/6/05
SRE and bung shackle 4/4.

detail of square tube on top tube.JPG
1373 hits | 98.18 KB | Posted: 5/6/05
Detail of square tube on end of main (upper) tube.

good view of front of bar and shackle assembly.JPG
1522 hits | 81.66 KB | Posted: 5/6/05
Good view of bar and shackle assembly 1/2.

good view of front of bar and shackle assembly.JPG
1853 hits | 95.57 KB | Posted: 5/6/05
Good view of square tube and shackle assembly 2/2.

wrap bar template.jpg
2481 hits | 42.83 KB | Posted: 6/6/05
This is the template for the steel that welds onto the rear axle. The two peices are 1/4" steel tha...