TGMotorWiring.JPG
27657 hits | 61.24 KB | Posted: 12/4/08

Tailgate Motor Wiring '92-95 (other years similar)
IF THE IMAGE IS TOO SMALL, click it.
The 2 Purple...
RwdoSws87-91.jpg
301 hits | 43.78 KB | Posted: 3/13/21

'87-91 Bronco Rear Window Switches
TGpins96XL.JPG
6823 hits | 53.83 KB | Posted: 12/2/09

'94-96 Tailgate w/o Carpet

Unused carpet holes plugged with pushpins, indicating all '94-96 tailg...
TGcarpet.JPG
6928 hits | 49.66 KB | Posted: 10/17/10

'94-96 Bronco Tailgate Carpet

These t/g carpet pushpins have coarser fins than those for the camper...
TGCarpet93Mocha.JPG
3092 hits | 104.15 KB | Posted: 3/23/11

SOLD Mocha Tailgate Carpet

Pushpins included
TGCarpetBlue.JPG
5573 hits | 64.97 KB | Posted: 7/24/07

SOLD Bronco Tailgate Carpet

'94 Royal Blue fits '78-96 tailgates. Some mounting pushpins include...
TailgateCarpetMocha.JPG
6182 hits | 58.94 KB | Posted: 4/7/06

SOLD Tailgate Carpet NEEDS CLEANING

Ships as 5 lbs 62x21x3". I could roll it to try to reduce th...
Sliding.JPG
4811 hits | 74.58 KB | Posted: 8/14/11

When the glass (F2TZ9842006A) can be moved by hand, it usually means the motor's drive bushings have...
Tailgate O.JPG
12647 hits | 87.28 KB | Posted: 11/28/04

If the motor spins but won't move the glass (F2TZ9842006A), just push it down all the way, and you c...
End Seal.JPG
13200 hits | 116.55 KB | Posted: 7/7/03

If you only need to change the weatherbelts, or if the glass (F2TZ9842006A) needs to come out, remov...
Wthrblt5.JPG
2667 hits | 106.35 KB | Posted: 6/29/14

These aftermarket belts fit perfectly, and my original end seals are still in useable condition.

Th...
Weatherbelt.JPG
12579 hits | 96.51 KB | Posted: 7/7/03

AFTER removing the screw at each end, use a screwdriver to gently pry the OUTER weatherbelt up just ...
TGWthrBltOut.JPG
5795 hits | 44.77 KB | Posted: 9/24/07

SOLD Tailgate Outer Weatherbelts (D8TZ9841610A)

These are the belts that wipe the outside of the re...
Wthrblt2.JPG
2563 hits | 129.42 KB | Posted: 6/29/14

These aftermarket weatherbelts are shipped as a pair (as they should be) and are virtually identical...
Wthrblt4.JPG
2635 hits | 128.14 KB | Posted: 6/29/14

I apply dry (Teflon) lube to the flocked surfaces that touch the glass, and silicone spray to the ot...
Wthrblt3.JPG
2694 hits | 98 KB | Posted: 6/29/14

Perfect matches. The outer belt (D8TZ9841610A, E8TZ9841610A, F20207) is longer than the inner (F6TZ...
Weatherbelts.JPG
9867 hits | 31.64 KB | Posted: 11/28/04

This outer weatherbelt has begun to dry rot, and is already leaking water into the unpainted interio...
Tailgate I.JPG
10455 hits | 81.05 KB | Posted: 11/28/04

The wetness on the moisture barrier shows that the weatherbelts are dry-rotted & should be replaced ...
Wthrblt1.JPG
2754 hits | 125.87 KB | Posted: 6/29/14

One of several signs that the t/g weatherbelts are ruined is rain coming out of the access panel and...
TGshield.JPG
2770 hits | 127.53 KB | Posted: 6/29/14

The factory drip shield is just painted paper with duct tape along the bottom (which has never made ...
TGshiele.JPG
2555 hits | 120.86 KB | Posted: 6/29/14

This is a factory water shedder. It's taped along the bottom (the t/g is upside-down), and has a ta...
TGshielf.JPG
2646 hits | 118.75 KB | Posted: 6/29/14

The inner face of the water shedder is painted black so it doesn't absorb water QUITE as fast as if ...
Tailgate.JPG
12530 hits | 118.84 KB | Posted: 7/7/03

This can be done with the tailgate open or closed. After removing the inside access panel, remove t...
TGshielg.JPG
2925 hits | 118.99 KB | Posted: 6/29/14

This scrap of common plastic drop sheet should last much longer than the factory paper water shedder...
TGshieli.JPG
2871 hits | 116.83 KB | Posted: 6/29/14

Being very careful not to wrinkle the plastic, I applied a few strips of Gorilla tape along the top ...
TGshielj.JPG
2657 hits | 96.4 KB | Posted: 6/29/14

This was the REALLY tricky part: lifting the tape and sticking it to the t/g inner reinforcement bar...
TGshielk.JPG
2718 hits | 121.48 KB | Posted: 6/29/14

After the tape is secure along the top, the plastic sheet is unfolded and tucked so it SHOULD stay b...
Glass Up.JPG
11805 hits | 72.74 KB | Posted: 11/28/04

If the motor runs but doesn't move the glass (w/o defrost E0TZ9842006B, w/defrost F2TZ9842006A), pus...
Glass.JPG
14298 hits | 106.83 KB | Posted: 7/14/03

The L latch must be fully closed to defeat the safety interlock switch so the motor will run, so if ...
Inside L.JPG
11958 hits | 44.04 KB | Posted: 11/28/04

This is the optimum location for the glass since you have access to all the fasteners to remove the ...
Inside R.JPG
9518 hits | 35.22 KB | Posted: 11/28/04

The nuts for the glass track (red pointers) are under this fixed support, but the bolts for the regu...
NutsR.JPG
5206 hits | 84.33 KB | Posted: 8/14/11

The R nuts are covered by the structure, so a ratcheting boxend is the easiest tool to get at them. ...
RWdoBadGrid.JPG
6321 hits | 61.03 KB | Posted: 7/24/07

SOLD '80-96 Bronco Tailgate Glass (w/o defrost E0TZ9842006B, w/defrost F2TZ9842006A)

Defrost grid i...
56TGcrunchy.JPG
1854 hits | 78.79 KB | Posted: 6/10/15

Probably the most-common damage to a Bronco t/g: backing into a stationary object. Trees just don't...
TableGlass.JPG
5238 hits | 112.13 KB | Posted: 8/14/11

Most people are paranoid about breaking the glass (w/o defrost E0TZ9842006B, w/defrost F2TZ9842006A)...
Mechanism.JPG
10450 hits | 82.01 KB | Posted: 7/7/03

The 3 black bolts hold the center latch mechanism (remote control) and are used to align it so the h...
Inside C.JPG
14538 hits | 44.59 KB | Posted: 11/28/04

If the glass is clear of the shell, but you can't open the t/g, remove the inside access panel & pul...
Center Bolts.JPG
9298 hits | 46.65 KB | Posted: 11/28/04

Mark the bolt locations for reference, even if you plan to move the center mechanism later.
Mechanism In.JPG
10240 hits | 29.95 KB | Posted: 11/28/04

View from the driver's side

[url=http://www.supermotors.net/vehicles/registry/media/546453][img]htt...
Mechanism Side.JPG
9620 hits | 55.57 KB | Posted: 11/28/04

View from the passenger side

[url=http://www.supermotors.net/vehicles/registry/media/546453][img]ht...
RodClips.jpg
9210 hits | 27.44 KB | Posted: 11/28/04

To release the rods, push the hook end of the plastic clip off the rod so the plastic pivots in the ...
CenterMech.JPG
9310 hits | 51.45 KB | Posted: 5/17/07

Center mechanism front & back. Ford calls it the "remote control".

The rubber grommet fo...
Center Mechanism.JPG
9389 hits | 54.24 KB | Posted: 11/28/04

The center mechanism (remote control)
Center Mech.JPG
8619 hits | 64.91 KB | Posted: 11/28/04

The white plastic rod clips indicate the direction of each rod. Top of tailgate is top of photo. L...
Center Interlock.JPG
9232 hits | 60.26 KB | Posted: 11/28/04

The numbers show the sequence of events for PROPER operation of the inside latch handle. 5 & 6 shou...
Center Bent.JPG
9234 hits | 29.6 KB | Posted: 11/28/04

This is why the inside handle doesn't sit flat. If someone pulls the handle before the glass is ful...
RemBent.JPG
2884 hits | 118.03 KB | Posted: 4/21/14

I've never found a used tailgate whose remote was NOT bent, but this is among the worst.

[url=https...
Center Straight.JPG
8356 hits | 25.77 KB | Posted: 11/28/04

Fortunately, with the mechanism out, it's easy to straighten the bent lever. Spray it with WD-40 or...
TGCenterMech.JPG
6135 hits | 51.45 KB | Posted: 5/23/07

SOLD Tailgate Center Latch Mechanism from '95

Fits '78-96; includes all original fasteners, glas...
Center Gone.JPG
8731 hits | 55.31 KB | Posted: 11/28/04

To access the motor connector, push out these 2 retainers and pull the connector where you can see i...
Latch & Switch.JPG
11138 hits | 68.04 KB | Posted: 11/28/04

This is the safety interlock switch [url=http://www.amazon.com/dp/B0011DY1S2/]Motorcraft SW5163[/url...
Mechanism Inside.JPG
13006 hits | 82.57 KB | Posted: 7/7/03

The rod running to the Left (down) is the interlock rod that detects the glass being fully down. It...
Mechanism All.JPG
9739 hits | 73.53 KB | Posted: 11/28/04

This shows the interlock switch Motorcraft SW5163 in...
LatchClean.jpg
37 hits | 43.55 KB | Posted: 3/26/24

Tailgate (or Door) Latch Cleaning
IF THE IMAGE IS TOO SMALL, click it.

Latches that have not bee...
Latch Closed.JPG
10225 hits | 35.98 KB | Posted: 11/28/04

To operate the motor with the tailgate open, simply close the driver's latch. Be SURE to open it be...
TGRegulator.JPG
9330 hits | 60.58 KB | Posted: 5/17/07

'78-96 Bronco Tailgate Window Regulator front & back
(early regulator arms may have round swivels in...
RegMotor.JPG
4376 hits | 101.06 KB | Posted: 8/14/11

These motor screws aren't very tight in the threads, so I'm threadlocking them in. Since this motor...
Motor Bolts.JPG
8598 hits | 41.51 KB | Posted: 11/29/04

To access the motor, remove these 3 bolts (5/16" or 8mm 6-point head w/integral washer; 12-24x5...
Wire Unclipped.JPG
7980 hits | 36.81 KB | Posted: 11/29/04

To get enough slack in the wire to pull the motor out & work on it, remove the clip from the bottom ...
Motor Open.JPG
9111 hits | 54.99 KB | Posted: 11/29/04

If the window doesn't move while the motor is turning, it's likely that the bushings inside the moto...
Window Motor Gear.jpg
10026 hits | 48.91 KB | Posted: 11/29/04

This is the repair kit (DOAZ-62234A24-B $27.37 List; $20.53 in 2004), but you can also use 1/4"...
Motor Apart.JPG
10801 hits | 69.52 KB | Posted: 11/29/04

The pointers show what's left of the rubber insulators, which probably degraded faster due to the ex...
Motor97.JPG
4243 hits | 88.47 KB | Posted: 8/14/11

There are several stock motors that will fit & work, and this might be the fastest one I've found. ...
Regulator.JPG
8463 hits | 58.74 KB | Posted: 11/29/04

The motor drive's shaft aligns thru the hole in the top of the regulator. If the large gear is poppi...
Swingaway Brace.JPG
7853 hits | 71.44 KB | Posted: 11/29/04

Before removing the regluator, remove the tire carrier's strike brace (if equipped).

[url=http://ww...
Strike Bracket.JPG
7769 hits | 67.45 KB | Posted: 11/29/04

Later Broncos (~'90-96) have 3 bolts holding the strike to the bracket. Before that, there were onl...
TGSections.JPG
8914 hits | 30.26 KB | Posted: 7/29/07

'83-96 Bronco Tailgate in cross-sectional views

'78-82 is only different in the latches & interl...
TGTemplate.JPG
5769 hits | 59.72 KB | Posted: 10/13/10

Bronco Tailgate Emergency Access Templates

These allow 4 holes to be drilled in the tailgate inner ...
Regulator Remove.JPG
7368 hits | 82.08 KB | Posted: 11/29/04

With the regulator arms in this position (note the socket on the bolt in the regulator gear hole), a...
Regulator Out.JPG
7021 hits | 68.47 KB | Posted: 11/29/04

The regulator fits out the driver's side. On earlier Broncos, there is a brace here that must be re...
Tailgate Trim 86EFI.jpg
4894 hits | 14.61 KB | Posted: 7/12/03

SOLD Tailgate trim panel for 84-86 EFI Bronco

For a writeup on installation & alignment, read thi...
TGTrimRed.JPG
4556 hits | 57.56 KB | Posted: 9/10/07

SOLD '87-91 Bronco Tailgate Trim Panel with red reflector & all mounting hardware fits all '78-96 Br...
Trim Panel.JPG
8281 hits | 80.72 KB | Posted: 11/29/04

The trim panel can be removed after the access panel if the glass is rolled up out of the way. No o...
TGTrim95.JPG
4711 hits | 65.62 KB | Posted: 5/21/07

SOLD Tailgate Trim Panel from '95 Bronco (F2TZ-98425A34-A)

Fits '78-96; includes all original faste...
TG96.JPG
4512 hits | 29.89 KB | Posted: 7/24/07

SOLD '83-96 Bronco Tailgate from '96 Black EB, with '92-96 trim panel (F2TZ-98425A34-A)

Inside latc...
Tailgate TrimPanel.jpg
7977 hits | 46.91 KB | Posted: 10/14/05

Trim Panel '87-96

F-series A clips are plastic & fragile. Replacements have recently become availa...
TailgateLockParts.JPG
9522 hits | 38.01 KB | Posted: 7/7/06

Lock Cylinder for '78-96 Bronco tailgate
https://www.npdlink.com/product/lock-cylinder-and-keys-tai...
Switch C.JPG
8486 hits | 56.71 KB | Posted: 11/29/04

The tailgate key switch is 2 weather-resistant SPDT micro switches riveted into a bracket, and opera...
Switch Down.JPG
8559 hits | 47.95 KB | Posted: 11/29/04

When the key is rotated CW, the paddle presses the lower switch. The silver hairpin clip retains th...
Switch Up.JPG
7662 hits | 62.88 KB | Posted: 11/29/04

When the key is rotated CCW, the paddle presses the upper switch. Note the arrangement of parts on ...
Switch Off.jpg
6386 hits | 15.51 KB | Posted: 11/29/04

By removing ONLY the silver clip, the switch assembly can be removed from the lock cylinder.

I us...
Pad.JPG
5880 hits | 60.08 KB | Posted: 5/17/07

This pad is used to protect the tailgate paint from the rubber bumper on the bottom of the swingaway...
SwingawayPad.jpg
82 hits | 59.75 KB | Posted: 3/21/24

Swingaway Bump Pad
IF THE IMAGE IS TOO SMALL, click it.

Rather than drilling holes in a replacement...
Clip Remove.JPG
6235 hits | 62.56 KB | Posted: 11/29/04

To remove these clips (which are used on the frame also), push the pin in the center all the way thr...
Clip.JPG
5809 hits | 99.79 KB | Posted: 11/29/04

With the center pin out, the clip compresses, and can be pulled out of its hole.

[url=http://www.su...
Tailgate cables.JPG
6374 hits | 59.56 KB | Posted: 11/29/04

Early cable screws are #3 or #4 phillips; later ones are T-50. New cables are available from most p...
Torque Rod.JPG
7151 hits | 79.06 KB | Posted: 11/29/04

Before unbolting the tailgate from its hinges, first relieve the torque rod by bracing it against th...
TGTorqueRodBrkt.JPG
5622 hits | 58.28 KB | Posted: 9/12/07

The infamous torsion bar bracket. It cups up, so if it's allowed to collect dirt & rain, it rusts o...
TorsnRodAcc.JPG
3439 hits | 77.93 KB | Posted: 1/24/12

With the R hinge fully back, the torsion bar will BARELY fit out. Raising the hinge, or raising the...
TGTorqueRodRemv.JPG
6662 hits | 60.75 KB | Posted: 9/12/07

Torsion Bar Removal & Installation

The tailgate must be misaligned or removed to get the torsion ba...
TGplates.JPG
47 hits | 75.67 KB | Posted: 2/18/24

Tailgate Reinforcement Plates
IF THE IMAGE IS TOO SMALL, click it.
TGLatch78-82.JPG
6603 hits | 22.23 KB | Posted: 9/5/08

'78-82 tailgate latches are significantly different from '83-96. Because they mount differently in ...
StrikeBolt 78Bronco.jpg
7388 hits | 56.08 KB | Posted: 11/29/04

'78-82 Broncos used this type of strike bolt, and a different latch from '83-96. They are not inter...
StrikeBolt832.JPG
4899 hits | 70.46 KB | Posted: 6/13/09

This is an '83-96 tailgate strike bolt installed in the hole for a '78-82 type using a large angle-i...
Tailgate Cutaway.jpg
11262 hits | 68.86 KB | Posted: 11/29/04

Glass & Weatherbelts

The outside weatherbelt that wipes the glass (w/o defrost E0TZ9842006B, w/defr...
Xploded.JPG
5974 hits | 85.77 KB | Posted: 5/9/13

Exploded Tailgate
IF THE IMAGE IS TOO SMALL, click it.

[url=http://www.supermotors.net/vehicles/reg...
Prepped.jpg
76 hits | 38.47 KB | Posted: 3/19/24

New Tailgate Shell Prep
IF THE IMAGE IS TOO SMALL, click it.

New shells (which all come from the...
TGnew01.JPG
2575 hits | 128 KB | Posted: 4/21/14

The previous owner rear-ended this '96 XLT Sport, and installed a replacement t/g with a trim panel....
TGnew02.JPG
2489 hits | 105.15 KB | Posted: 4/21/14

Any automotive undercoating will significantly reduce the chances of tailgate (or door) rust, and I'...
TGnew03.JPG
2420 hits | 112.06 KB | Posted: 4/21/14

To perfectly center the swingaway strike bolt holes, first install the brace to the t/g, with this u...
TGnew04.JPG
2153 hits | 100.42 KB | Posted: 4/21/14

Reverse the dimples with the drill bit tip and they should be perfectly aligned with the bracket ins...
Xtract1.JPG
2152 hits | 115.16 KB | Posted: 4/21/14

The bottom hinge bolts commonly rust, seize, cross-thread, and break, so use a good bolt as a drift ...
Xtract2.JPG
2022 hits | 124.53 KB | Posted: 4/21/14

Grind the broken bolt flat & flush with the nut plate on both sides, center punch it, and drill 5/16...
Xtract3.JPG
2118 hits | 125.73 KB | Posted: 4/21/14

Use a file to carefully remove the remaining bolt until only its thread is left. Using a rough file...
Xtract4.JPG
2158 hits | 109.97 KB | Posted: 4/21/14

Chase the nut plate with a 3/8"-16 tap so the bolt goes in easily, then apply anti-seize lube (...
Tailgate Latch 83-96.jpg
14769 hits | 88.89 KB | Posted: 8/23/05

'83-96 Bronco Tailgate Latches

ERRORS: there are several 6s & 7s...

1 - Tailgate Latch Remote Cont...
Tailgate Latches.jpg
8605 hits | 51.48 KB | Posted: 11/29/04

'78-82 Latches

The torsion bar retainer (430A32) in View C is available from Dennis Carpenter as [u...
TailgateLatches.jpg
8936 hits | 88.51 KB | Posted: 10/14/05

Latches

1 Tailgate Latch Remote Control D8TZ-9843170-B (JBG [url=https://shop.broncograveyard.com/1...
TGHinges.JPG
4142 hits | 37.13 KB | Posted: 5/17/07

SOLD Tailgate Hinges

Fit '78-96
Normal wear

For a writeup on installation & alignment, read t...
TGBedWeatherstrip.JPG
6915 hits | 65.55 KB | Posted: 9/29/07

Tailgate Threshhold Seal '78-96

Note that the body style shown is '78-79 (taillight & strike mounti...
TgTracks.jpg
169 hits | 39.71 KB | Posted: 8/9/22

The internal glass runs commonly dry-rot and break a...
TGThreshhold.JPG
4043 hits | 29.66 KB | Posted: 4/21/07

SOLD Bronco Tailgate Threshhold
TGThreshold.jpg
32 hits | 41.06 KB | Posted: 2/19/24

Bronco Tailgate Weatherstrip & Threshold
IF THE IMAGE IS TOO SMALL, click it.
TGThreshholdBk.JPG
3422 hits | 100.22 KB | Posted: 7/24/07

SOLD Bronco Tailgate Threshhold from '92-96 fits '78-96
Tailgate Torsion 8396.jpg
7708 hits | 79.58 KB | Posted: 10/16/05

Hinges, Torque Rod, & '83-96 Strikes. The strike bolt is the only thing in this diagram specific to...
Tailgate Torsion 7882.jpg
7108 hits | 59.41 KB | Posted: 11/29/04

78-82 Strikes & Torque Rod. The strike bolt, cable bolts, & support are the only things in this dia...
StrikeGap1.JPG
3931 hits | 84.1 KB | Posted: 6/13/09

The tailgate gap should be the same at the top as at the bottom. If it's too wide at the top, the b...
StrikeGap2.JPG
4391 hits | 57.18 KB | Posted: 6/13/09

The best way to bend the bedwalls inward is with a large ratchet strap hooked into the body crossmem...
TGdentPull.jpg
1764 hits | 126.7 KB | Posted: 6/10/15

Undentation

The best way to remove any dent is to apply force in exactly the opposite direction tha...
LatchIndicator.JPG
8424 hits | 48.95 KB | Posted: 5/20/12

Bronco Tailgate Safety Latch Light

[url=http://www.supermotors.net/registry/media/71412][img]http:/...
LatchLighu.JPG
5564 hits | 64.51 KB | Posted: 3/5/13

Tailgate Latch Light indicates that the latch is not fully closed when attempting to operate t/g win...
TGCircuit.JPG
11157 hits | 31.42 KB | Posted: 3/15/09

The Bronco tailgate window circuit is a common (Ford) polarity-reversing circuit with 2 switches. E...
TGcircuitMods.JPG
15643 hits | 76.3 KB | Posted: 6/28/12

Modified Bronco Tailgate Window Circuit
IF THE IMAGE IS TOO SMALL, click it.

'92-96 shown; '87-91 s...
Tailgate Window Circuit.jpg
13343 hits | 33.93 KB | Posted: 11/29/04

Window Motor Circuit from http://www.fordfuelinjection.com/
Note that the internal circuitry for th...
Tailgate Defrost Circuit Early.jpg
6025 hits | 29.67 KB | Posted: 11/29/04

Defrost Circuit '78-86

http://fordfuelinjection.com/
TGWiring.JPG
8583 hits | 82.91 KB | Posted: 6/30/12

'78-96 Bronco Tailgate Wiring

1 - Switch and Housing Assembly (Includes 14086 Wiring) - 14046
2-...
TGconnLoc.jpg
55 hits | 62.79 KB | Posted: 2/18/24

'92-96 Bronco Tailgate Connector Location
IF THE IMAGE IS TOO SMALL, click it.

See also:
[url=h...
C418.JPG
7938 hits | 66.26 KB | Posted: 9/12/07

This is all the wiring for the tailgate, except the ground for the defrost grid. This connector is ...
TGWiring96.JPG
6033 hits | 53.95 KB | Posted: 9/12/07

Note that there is no connector near the ground wire, which is forward of the L taillight. C418 is ...
TGdashSw92-96.JPG
4064 hits | 69.04 KB | Posted: 11/20/09

F2TZ-14529-A Motorcraft SW7071 ~$25~65.
92s.JPG
5883 hits | 72.44 KB | Posted: 11/10/05

Some tailgates split here on the R side at the top due to the stress applied by the outside tire car...
FenderBrace.JPG
6808 hits | 61.01 KB | Posted: 4/1/06

The swingaway brace inside the R quarter panel is spot-welded & riveted into place BEFORE the outer ...
TGswHairpin.jpg
337 hits | 39.04 KB | Posted: 2/12/21

This can be used as a pattern to bend a replacement clip from an appropriate wire, like the spring f...
TGSwitch1.JPG
8141 hits | 50.5 KB | Posted: 5/17/07

Tailgate Window Switch

The switch is actually 2 SPDT microswitches which aren't designed to be se...
TGSwitch2.JPG
6374 hits | 68.66 KB | Posted: 5/18/07

Tailgate Switch Wiring Colors

These wires are not intended to be removed from the switches, and the...
TGSwitch3.JPG
7473 hits | 56.55 KB | Posted: 5/18/07

Tailgate Switch Paddle

When the tailgate lock cylinder is turned, this paddle arm swings around &...
TGSwitch4.JPG
6329 hits | 40.35 KB | Posted: 5/18/07

Tailgate Switch Paddle

When the key is removed from the tailgate lock cylinder, the paddle is in ...
TGSwitch5.JPG
8312 hits | 49.3 KB | Posted: 5/18/07

Tailgate Safety Switch

Y/R is NC to Pu/LG
Br/Bk (Tn/Bk) is NC to Pu/LB
When a switch is depressed b...
TGSwitch.JPG
5700 hits | 53.64 KB | Posted: 7/24/07

SOLD Bronco Tailgate Switch from '94 fits '78-96

For a writeup on installation & alignment, read ...
TGharness89.jpg
382 hits | 70.48 KB | Posted: 10/5/22

SOLD Bronco Tailgate Wiring Harness, non-defrost, early 3-blade connector
IF THE IMAGE IS TOO SMALL,...
TGHarness90.JPG
5944 hits | 49.09 KB | Posted: 9/26/07

SOLD Bronco Tailgate Wiring Harness from '90 fits '80-91

[url=http://www.supermotors.net/registry...
TGHarness95.jpg
6822 hits | 45.32 KB | Posted: 5/17/07

Tailgate Wiring Harness from a '95 Bronco with defrost.

[url=http://www.supermotors.net/registry/...
TGHarness86.JPG
4566 hits | 45.47 KB | Posted: 9/21/08

SOLD Tailgate Harness fits '78~90 with or w/o defrost.

[url=http://www.supermotors.net/registry/m...
TGHarness95.jpg
6558 hits | 45.32 KB | Posted: 5/17/07

Tailgate Wiring Harness from '95 Bronco with defrost

[url=http://www.supermotors.net/registry/med...
TGAccessPnl.JPG
3932 hits | 101.96 KB | Posted: 4/10/06

SOLD Tailgate Access Panel (D8TZ9840704A) fits '78-96 Bronco tailgates. No rust, dents, wear, or wa...
TGAccess.JPG
3884 hits | 49.28 KB | Posted: 5/15/07

SOLD Tailgate Access Panel (D8TZ9840704A)

The white mess is just paper that got dissolved by rain.
...
AccessPanels.JPG
3790 hits | 58.44 KB | Posted: 7/24/07

SOLD Tailgate Access Panels (D8TZ9840704A) for '78-96 Broncos (white)

For a writeup on installation...
TG90.JPG
3548 hits | 55.49 KB | Posted: 7/13/07

SOLD '83-96 Bronco Tailgate from '90 EB

Motor needs bushings. Inside latch handle doesn't lie fl...
90TGcrate.JPG
3979 hits | 72.94 KB | Posted: 7/22/07

SOLD Tailgate from '90 EB Bronco

I had to remove the trim panel & sheet one side in cardboard to ge...
TG96Crated.JPG
5375 hits | 57.25 KB | Posted: 10/2/07

96 Tailgate Crated

Crating materials cost ~$50 in 2007.
TGRed.JPG
1173 hits | 59.08 KB | Posted: 2/2/13

SOLD Red Tailgate Shell E8TZ-9840700-A
IF THE IMAGE IS TOO SMALL, click it.

[url=https://www.superm...
TailgateBurg.jpg
279 hits | 36.53 KB | Posted: 12/22/21

SOLD Burgundy Bronco EB Tailgate Sep.21
IF THE IMAGE IS TOO SMALL, click it.
This is now stripped to...
TailgatesBurgMrn.jpg
357 hits | 68.22 KB | Posted: 6/20/20

Junkyard reddish tailgate shells E8TZ-9840700-A
SOLD both.
IF THE IMAGE IS TOO SMALL, click it.

Act...
TG95RedBent.JPG
1393 hits | 37.53 KB | Posted: 2/20/12

SOLD Red '95 Bronco EB Tailgate
IF THE IMAGE IS TOO SMALL, click it.
This is now stripped to an empt...
TGSkin90Bk.JPG
3776 hits | 77.57 KB | Posted: 9/10/07

SOLD Empty Bronco Tailgate Shell & Access Panel fits '83-96 Broncos. There are a few other small ch...
TGTrimB88.JPG
2547 hits | 114.08 KB | Posted: 2/20/12

SOLD '87-96 Bronco Tailgate Trim Panel w/o trim strip

Black strip (only) w/oval & fasteners F2TZ-98...
BumperFillerR.JPG
2286 hits | 40.64 KB | Posted: 10/26/08

SOLD Rear Bumper Filler for '80-96 Bronco with step bumper & NO body lift

[url=http://www.supermo...
TGFillerB.JPG
2064 hits | 69.95 KB | Posted: 6/28/11

SOLD Filler between Bronco tailgate & bumper for stock body height. All original fasteners included...
Tailgate Defrost Circuit.jpg
5995 hits | 27.24 KB | Posted: 11/29/04

Defrost Circuit '92-96

'87-91 similar

http://fordfuelinjection.com/
TGSwitchC274.JPG
5914 hits | 36.71 KB | Posted: 4/26/07

Pinout for '87-96 Dash Switch CONNECTOR (harness side) for Tailgate Window
(Looking into the switch...
tailgate-window-circuit-aux.JPG
6589 hits | 43.25 KB | Posted: 11/15/06

Auxilliary t/g window switch circuit for '78-86 Broncos. This design is fairly simple, but requires...

About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2024 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog