1990 Ford Bronco
Owner: Clint Russell 
From: Murfreesboro, TN, U.S.A.        (Other registries in TN)
Year, Make, & Model: 1990 Ford Bronco        (Other Ford Broncos in this club)
Avatar:
Clubs: SuperFord.org        (Other vehicles in this club)
Nickname: The Bronco
Mileage:
Engine: 5.8 EFI, MSD ignition, JBA Shorty's, K&N filter
Drivetrain: 9" rear axle w/ ARB and Disc brakes. The tranny is the E4OD. 5.13 gears
Notes: Full interior Dynamat sound suppression, custom rock sliders, Autofab 16" front wheel travel kit, 3" body lift, warn maual hubs, york compressor system, dual optima batteries, extra storage compartment, energy suspension bushings.

This project started in 1994 when I bought the 1990 ford bronco for $7800. It had 146,000 miles. I drove it till 1997 when in March the intake gasket blew, the tranny tailshaft broke and I was getting 7 miles a gallon. So my father stored it for me because he always wished he had saved his first car. (And because I love this truck) In 1998 I bought a totaled out 1994 bronco for the frame, engine and front axle. So here it is after 5 years the bronco finally drove under its' own power around the block for the first time.
Last Updated: 10/3/2003
Hits: 9501
Album
Folder Hits Comments Created Updated
folder General3003,559010/3/0310/3/03
folder Dyanmat3003,570010/3/0310/3/03
folder Rear Brakes3003,279010/3/0310/3/03
Newest Media Files
DSC00060.JPG
1255 hits | 61.99 KB | Posted: 10/3/03

Perparing for the Autofab lift
batterytray2a.jpg
1109 hits | 16.98 KB | Posted: 10/3/03

finishedreaviewbrakesa.jpg
1030 hits | 11.29 KB | Posted: 10/3/03

rearbrakeside2a.jpg
1144 hits | 10.72 KB | Posted: 10/3/03

After using a pervious design I saw on the net I had these brackets laser cut and they seem to work well. If I was doing it again I would rotate the caliper around the axle so the bleeder is positioned on top.
finishedrearbrakea.jpg
1105 hits | 5.51 KB | Posted: 10/3/03

frontdyna1a.jpg
1162 hits | 10.98 KB | Posted: 10/3/03

Apillardynaa.jpg
1251 hits | 8.02 KB | Posted: 10/3/03

reardyna4b.jpg
1157 hits | 9.1 KB | Posted: 10/3/03

Here is the covered body
broncorivergraya.jpg
1195 hits | 29.6 KB | Posted: 10/3/03

Most Viewed Files
DSC00060.JPG
1255 hits | 61.99 KB | Posted: 10/3/03

Perparing for the Autofab lift
Apillardynaa.jpg
1251 hits | 8.02 KB | Posted: 10/3/03

broncorivergraya.jpg
1195 hits | 29.6 KB | Posted: 10/3/03

frontdyna1a.jpg
1162 hits | 10.98 KB | Posted: 10/3/03

reardyna4b.jpg
1157 hits | 9.1 KB | Posted: 10/3/03

Here is the covered body
rearbrakeside2a.jpg
1144 hits | 10.72 KB | Posted: 10/3/03

After using a pervious design I saw on the net I had these brackets laser cut and they seem to work well. If I was doing it again I would rotate the caliper around the axle so the bleeder is positioned on top.
batterytray2a.jpg
1109 hits | 16.98 KB | Posted: 10/3/03

finishedrearbrakea.jpg
1105 hits | 5.51 KB | Posted: 10/3/03

finishedreaviewbrakesa.jpg
1030 hits | 11.29 KB | Posted: 10/3/03

Maintenance & Modification Logs
This user hasn't added any log entries, yet.
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2024 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog