IMG_0442.JPG
1546 hits | 41.2 KB | Posted: 6/21/04

Here's what you get. Last year the dealer hosed me $26 just for 12 new alan screws and these come fr...
IMG_0148.JPG
1123 hits | 49.99 KB | Posted: 1/10/05

What special tools are needed ? Just a philips, 9/64" alan wrench, a pick tool and some spreading ci...
IMG_0057.JPG
1129 hits | 52.29 KB | Posted: 1/10/05

There's the ugly truth in all it's salt encrusted glory. The dealer wanted $65 CDN just for the red ...
IMG_0061.JPG
972 hits | 44.37 KB | Posted: 1/10/05

Begin by pulling the alan bolts out and pray you put plenty of Anti-seize on their threads last tim...
IMG_0073.JPG
988 hits | 48.56 KB | Posted: 1/10/05

Next out comes the philips screw.
IMG_0076.JPG
1045 hits | 65.82 KB | Posted: 1/10/05

Now remove the spring and sprag.
IMG_0079.JPG
1065 hits | 68.49 KB | Posted: 1/10/05

Now you should have plenty of room to access the circlip in the center with the circlip pliers.
IMG_0084.JPG
1305 hits | 66.17 KB | Posted: 1/10/05

Man this pick tool is so useful. I used to play around with small screwdrivers for minutes trying to...
IMG_0089.JPG
1072 hits | 46.68 KB | Posted: 1/10/05

Using the two screw trick, so many people here told me to use, just pull the rest out and you're fre...
IMG_0065.JPG
1121 hits | 55.86 KB | Posted: 1/10/05

Right from MileMarker to you ! Being a cabin dwelling Canadian I don't use grease in the outer hub ...
IMG_0094.JPG
1207 hits | 59.26 KB | Posted: 1/10/05

Anti-seize compound and plenty of it. My pipe bending mechanic buddy tipped me off to this stuff in ...
IMG_0097.JPG
1575 hits | 57.07 KB | Posted: 1/10/05

Push and pack it in liberally, both ends.
IMG_0092.JPG
1538 hits | 56.14 KB | Posted: 1/10/05

I also slap quite a bit on Anti-seize inside the housing as well.
IMG_0100.JPG
1110 hits | 55.73 KB | Posted: 1/10/05

Then gently push in the new MileMarker innards making sure you don't push the innermost spline back ...
IMG_0102.JPG
1028 hits | 57.43 KB | Posted: 1/10/05

If you haven't pushed the inner spline back too far, the circlip from MileMarker, will go on easy as...
IMG_0104.JPG
1115 hits | 63.41 KB | Posted: 1/10/05

Now slip in the outer housing retaining ring, also provided new in the kit from MileMarker.
IMG_0105.JPG
964 hits | 61.08 KB | Posted: 1/10/05

I can't help myself ! I even slapped more Anti-Seize in the 9/10ths twist threads of the MileMarker ...
IMG_0107.JPG
985 hits | 58.59 KB | Posted: 1/10/05

The MileMarkers pushed in snugly but with only hand pressure, seating nicely into the hub housing. N...
IMG_0112.JPG
1265 hits | 45.88 KB | Posted: 1/10/05

More Anti-Sieze into the threads of the new alan bolts, again provided in the kit , and then install...
IMG_0114.JPG
1221 hits | 51.21 KB | Posted: 1/10/05

Next re-employ the same 9/64ths alan wrench as the stock bolts took and tighten down all six bolts i...
IMG_0124.JPG
952 hits | 58.19 KB | Posted: 1/10/05

The alan screws provided with the hubs, unlike Warns, are identical in size, diameter, length and t...
IMG_0117.JPG
1096 hits | 49.32 KB | Posted: 1/10/05

Just for the heck of it I timed myself on the other side and it took 7 minutes to swap over from sto...

About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2024 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog