IMG_0001.JPG
908 hits | 67.18 KB | Posted: 1/14/05
Even the best breaks eventually. I'd been trying to trace the belt squeal for about 6 months. Even...

IMG_0083.JPG
854 hits | 47.26 KB | Posted: 1/14/05
Got another remanufactured Cardone Saginaw for "my 78 Ford Econoline van" for cheap enough to replac...

IMG_0005.JPG
946 hits | 75.49 KB | Posted: 1/14/05
Started by undoing the low pressure return line's hose clamp, visible on hose.

IMG_0009.JPG
834 hits | 59.41 KB | Posted: 1/14/05
Slacking off this half inch cooler pipe retaining clamp bolt helps get the hoses off and on. Just re...

IMG_0013.JPG
814 hits | 51.3 KB | Posted: 1/14/05
I wanted to flush my old fluid out, even though it was clean to look at I'm sure there were filings ...

IMG_0019.JPG
793 hits | 56.76 KB | Posted: 1/14/05
Next, before you slack any mounting bolts, crack loose the high pressure hose fitting. It's easier n...

IMG_0021.JPG
835 hits | 42.42 KB | Posted: 1/14/05
Then just loosen off and whip out the two mounting bolts.

IMG_0022.JPG
810 hits | 65.52 KB | Posted: 1/14/05
Off comes the belt and out comes the pump, leaking and spilling all over the place.

IMG_0031.JPG
790 hits | 66.01 KB | Posted: 1/14/05
Clamped her into the vice so it's easier to work on.

IMG_0034.JPG
815 hits | 64.13 KB | Posted: 1/14/05
A little of your favourite penetrating oil onto the shaft will help the pulley come off more easily...

IMG_0029.JPG
849 hits | 57.31 KB | Posted: 1/14/05
Borrowed a PS pulley puller tool kit from a local jobber to re and re the pulley without damaging th...

IMG_0040.JPG
844 hits | 69.81 KB | Posted: 1/14/05
Why use a ractchet when a two foot flex bar can do the job so much more easily, and they wonder how ...

IMG_0043.JPG
794 hits | 68.21 KB | Posted: 1/14/05
Now just undo the bolts and stud and transfer the bracket onto the remanufactured Saginaw.

IMG_0046.JPG
759 hits | 54.91 KB | Posted: 1/14/05
Mine had one stud on the back of the pump to hold the 78 van bracket on with a nut.

IMG_0049.JPG
826 hits | 59.64 KB | Posted: 1/14/05
A little synthetic grease onto the shaft to help the pulley slide/pull on.

IMG_0051.JPG
917 hits | 74.74 KB | Posted: 1/14/05
The pulley puller also installs the pulley onto the new pump shaft very well, by tightening it up un...

IMG_0054.JPG
745 hits | 49.65 KB | Posted: 1/14/05
I choose to put the new low pressure hose on now, while it's on the bench and easy to tighten the tw...

IMG_0065.JPG
779 hits | 53.1 KB | Posted: 1/14/05
To flush the pump I've already added that clear hose to the low pressure return pipe of the cooler a...

IMG_0085.JPG
844 hits | 64.13 KB | Posted: 1/14/05
I had been using the synthetic stuff on the right, but I'm going to flush it out and use the regular...

IMG_0078.JPG
1005 hits | 75.28 KB | Posted: 1/14/05
There's my new canned ham all bolted up in place and filled up with fluid ready to flush through.

IMG_0070.JPG
794 hits | 46.69 KB | Posted: 1/14/05
Now that the flushing is done I removed the clear hose and installed the new PS hose with two oppose...